Recent content by tuxbobble

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. tuxbobble

    First try at a full packer...and some questions...

    Almost ordered that exact glove yesterday since it went on sale. I stopped myself thinking I'd have less dexterity and do a worse job of it, but if it's manageable maybe I'll go back and place an order. Thanks for the input.
  2. tuxbobble

    First try at a full packer...and some questions...

    That's a really good tip about the extra probes. My Maverick takes two so having a couple of extras and swapping outside the drum might be a good way to deal with it. As for the cook time, it's possible I pulled the butt too early. The flat was done even further ahead of schedule, so I left it...
  3. tuxbobble

    First try at a full packer...and some questions...

    I finally got around to finding a good butcher shop where I could get a full packer brisket. I've only ever done flats before, but burnt ends have been calling my name for too long to ignore. Seems like there are mixed opinions about smoking it whole and cutting after, vs separating beforehand...
  4. tuxbobble

    First try at a UDS

    This is very similar to what I had for my ECB, but the rope I have seems too thick. I'll probably use it ad hoc without the silicone temporarily and see if things get better, and make it permanent if it seals nicely I was mostly worried about the seal where id need to cut it since it won't be...
  5. tuxbobble

    First try at a UDS

    Is http://www.bubbasbarrels.com/lever-lock-ring-55g-drums the best option available to help seal up the lid? I saw one on websites that people said wouldn't fit their 55gallon drum, or isn't easy to open/close, etc. I have some rope gasket for a stove/oven that I've used on my ECB but it seems...
  6. tuxbobble

    First try at a UDS

    One more thing. Do folks typically paint their pipe caps and nipples? I noted a bit of rust starting to form even after just a couple of sessions I can paint them easily enough, but wasn't sure if people advise against painting the part that goes inside the drum, or the interior of the pipe...
  7. tuxbobble

    First try at a UDS

    Intake nipples are definitely leaking slightly. I had bought some oven safe sealant that I was going to use on my ECB to attach rope gasket but never did, so I'll probably use that around the nipples since it should be high temp safe. As for the gasket I'll have to look for one. I'm sure...
  8. IMG_20170722_144648.jpg

    IMG_20170722_144648.jpg

    • tuxbobble
    • Media item
    • Comments: 0
    • Album: First try at a UDS
  9. tuxbobble

    First try at a UDS

    I haven't sealed the leak yet but it seems to me like the only major swings I've had have come in big spikes when I've popped the lid off to add other meats. Unfortunately today I'm doing 3 differently timed cooks in the one drum, trying to get them to come off close to the same time. 6 hour...
  10. tuxbobble

    First try at a UDS

    Thanks Dave. I'll have to see what I can come up with. The other night it was dark/rainy so it was hard to see but today I'm noticing a pretty significant air leak. It seems like the lid may be bowed slightly so I may need to figure out a way to clamp it on opposing sides. Like you mentioned...
  11. tuxbobble

    First try at a UDS

    Thanks Dave. It seemed pretty tight but I'll take a closer look when I use it tomorrow. Any tips on improving the seal if it's not airtight aside from the exhaust pipes?
  12. tuxbobble

    First try at a UDS

    Quick preview of the results so as not to leave anyone hanging. The picture didn't come out as good as it looked in person. Might have been able to take it off a little earlier if not for the heavy rain. Like I said, this was a small temperature test, but hopefully the main event will come over...
  13. IMG_20170720_214005.jpg

    IMG_20170720_214005.jpg

    • tuxbobble
    • Media item
    • Comments: 0
    • Album: First try at a UDS
  14. tuxbobble

    First try at a UDS

    Good tips. I have 3 in/3 out pipes. 2 of each I'm just using as on/off using caps, and the other of each is a valve for now. That may change over time. I did a really quick test last night by putting some kielbasa on for an hour. The temps ranged from 210-280, with one intake closed. I...
  15. First try at a UDS

    First try at a UDS

See more
Top Bottom
Back
Clicky