Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. socalcooker

    Another 120 gallon reverse flow

    I get same temp across the grate within 10 degrees. If I go and build a crazy fire in it I’ll get as much as 50 degrees difference from one end to the other. It all comes down to fire management. I put the upper vent on my first build and like I said it’s always closed. I tried to use it but...
  2. socalcooker

    Another 120 gallon reverse flow

    If you’d look back a few comments you’d see we already went over this. Not a fan of the upper inlets that you are constantly promoting for whatever reason. A properly designed smoker with the right size openings and exhaust doesn’t need that extra opening. I can cold smoke on my 60 gallon RF...
  3. socalcooker

    Another 120 gallon reverse flow

    Finally finished this smoker. Put some casters on it, fabbed the charcoal basket, a fire poker, and an ash clean out tool that doubles as a way to pull out and push in the charcoal basket. The charcoal basket is pretty heavy. I put platform grate in the bottom and expanded metal over that...
  4. socalcooker

    Another 120 gallon reverse flow

    Got a lot done over the last few weeks. Door and counter weight are done. Exhaust is on there along with the cap. Grate is done. Base is all done except wheels. Put in temp probe ports. Got the firebox door put back on. I spent most of today cleaning up weld spatter and filling and...
  5. socalcooker

    Another 120 gallon reverse flow

    Got a lot done in the last couple weeks. RF plate and drain are in. The RF plate has a half inch drop from the ends to the center. The center section I tacked to the tank then pushed down to make a trough. Poured some water in there and it drains pretty well. I put a flat spot on the FB for...
  6. socalcooker

    Another 120 gallon reverse flow

    I put it on my first smoker based off of info from this site. But I’m able to control my temps better with it closed. Temps fluctuated much more when trying to use it. I also get a very clean burning fire with no visible smoke most of the time. Not sure why it didn’t work out on my cooker...
  7. socalcooker

    Another 120 gallon reverse flow

    Not a fan of the upper inlet. I put one on my first build and it’s always closed.
  8. socalcooker

    Another 120 gallon reverse flow

    Got the cook chamber door cut out today and the opening from FB to CC. Door warped a little but didn’t look like it was gonna be to bad.
  9. socalcooker

    120 gallon RF trailer build

    Long time since an update. The trailer is on hold for a while. My buddy I’m building it for, his wife was diagnosed with breast cancer. So for the time being I delivered the smoker so they can use it. This was the first cook. St. Louis ribs, pork belly burnt ends, and beans. Will eventually...
  10. socalcooker

    Another 120 gallon reverse flow

    Been a long time since I’ve been able to work on this. Just got going on it again in the last couple weeks. Cut out and patched where the valves were and the name tag was so rusted I decided to just cut it out and patch it as well. I cut the opening from FB to CC and got them welded together...
  11. socalcooker

    120 gallon RF trailer build

    Actually I was going to put the seam opposite of the cooker, but now that you mention it I may put it under the cooker to be less noticeable. Kyle
  12. socalcooker

    120 gallon RF trailer build

    Got quite a bit done the last few days. All the cross members are tacked in ready to weld up. I cut the boat cross member from the rear and replaced with a flat peice. The diamond plate is just laying on there to mark where my Jr beams will go. Happy new year everyone!
  13. socalcooker

    120 gallon RF trailer build

    The trailer is 5’9” wide and I can only get diamond plate 5’x10’. So I’m going to have a very long weld seam pretty much the length of the trailer. I think I will get the frame sandblasted before the diamond plate goes on just to avoid any problems with rust down the road. Kyle
  14. socalcooker

    120 gallon RF trailer build

    Finally got a chance to work on the trailer some. I’ve got most of the cross beams tacked in. Still need a few in the tongue area and I need to cut the rear cross member out as it’s dropped for a boat. Then I’ll replace it with a flat peice. The other existing cross members will stay. I...
  15. socalcooker

    5000 Liter animal recycler

    When is the first cook? I want to see it going. Kyle
  16. socalcooker

    Another 120 gallon reverse flow

    I was able to get the handle and latch done except for the spring handle part. I might add a brace onto the latch portion. It seems to flex a little to much when I push the handle into the slot rather than compressing the gasket. It's 1/2"X1.5" but I guess it's sticking out there far enough...
  17. socalcooker

    120 gallon RF trailer build

    I'm not going to sandblast it myself, way to much trailer for that little blaster. I'm going to cut a section from that other tank to use as a FB for a 300 gallon tank I just picked up. At least that's the plan at the moment. I may use that tank whole for a smoker. But I've got that 300...
  18. socalcooker

    300 gallon tank

    Picked this tank up today. Gonna do a RF on a trailer for big parties and maybe some catering. Kyle
  19. socalcooker

    120 gallon RF trailer build

    Finally got a suitable trailer for this thing. Got it moved in today. Gonna start adding cross members for the diamond plate. Kyle
  20. socalcooker

    First smoker build need help,60 gallon air tank

    I ran my plate up to the dome weld on the opposite end. You want the opening to be about the same as the opening as you have from the firebox to cook chamber. Weld a piece of flatbar on edge at the end of the plate to stop grease from dripping under the plate. Put your plate above that 5.75"...
Top Bottom
Back
Clicky