Recent content by rollnthunder

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. image (9).jpeg

    image (9).jpeg

    • rollnthunder
    • Media item
    • Comments: 0
    • Album: Need some input and help with finishing reverse flow smoker i picked up.
  2. image (8).jpeg

    image (8).jpeg

    • rollnthunder
    • Media item
    • Comments: 0
    • Album: Need some input and help with finishing reverse flow smoker i picked up.
  3. rollnthunder

    Need some input and help with finishing reverse flow smoker i picked up.

    The top of the firebox is roughly 2" above the reflector plate.Also here is a pic of what the intake setup is like also a pic of the opening in the firebox to cc
  4. rollnthunder

    Need some input and help with finishing reverse flow smoker i picked up.

    I will take a pick of the intake system its undersized as well i think. Thanks for the all help i will check on the other things you asked for. Im also not sure how much of the reflector plate is welded in i may be able to raise it with some work. 
  5. rollnthunder

    Need some input and help with finishing reverse flow smoker i picked up.

    The top of the smoker is 11.5" wide the height from the very bottom of the cook chamber under the reflector plate to the lowest part of the door is 12" the distance from the bottom to the reflector plate is 5.25". The stack is 3" diameter and is 13" tall and extends into the cook chamber about...
  6. IMG_0437.JPG

    IMG_0437.JPG

    • rollnthunder
    • Media item
    • Comments: 0
    • Album: Need some input and help with finishing reverse flow smoker i picked up.
  7. IMG_0435.JPG

    IMG_0435.JPG

    • rollnthunder
    • Media item
    • Comments: 0
    • Album: Need some input and help with finishing reverse flow smoker i picked up.
  8. IMG_0430.JPG

    IMG_0430.JPG

    • rollnthunder
    • Media item
    • Comments: 0
    • Album: Need some input and help with finishing reverse flow smoker i picked up.
  9. rollnthunder

    Need some input and help with finishing reverse flow smoker i picked up.

    Thanks for the reply I have not cooked on it yet since it was bought unfinished. He has the 1/4" heat reflector plate in and he welded angle iron along the front and back wall for the supports of the grates which need to be built I figured I would just use some 1" square tube and make the frame...
  10. Need some input and help with finishing reverse flow smoker i picked up.

    Need some input and help with finishing reverse flow smoker i picked up.

  11. rollnthunder

    Need some input and help with finishing reverse flow smoker i picked up.

    I picked up this reverse flow project and have been checking out alot of the threads on this forum and wow there is alot of info. First a little about the pit. Its  CC measures 24"Wx60"Lx28"H the FB measures 24x24x24 and i measured the hole going from the FB to CC and its 2 3/4"x16" also...
  12. IMG_1916[1].JPG

    IMG_1916[1].JPG

    • rollnthunder
    • Media item
    • Comments: 0
    • Album: Need some input and help with finishing reverse flow smoker i picked up.
  13. rollnthunder

    Newbie from michigan

    Well im from southeast lower part of michigan and i have been playing around with a pellet smoker for a while and just picked up a reverse flow stick burner on a trailer. IT needs some work and i im not sure about a few things on it or if they are done correctly. With that said i will be reading...
See more
Top Bottom
Back
Clicky