Recent content by davidski

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. davidski

    My Oklahoma Joe Longhorn BLOG

    Ive been asked to provide URLs to where i got the tuner and latches. URLs are by the pictures. 
  2. davidski

    My Oklahoma Joe Longhorn BLOG

    Hey, did you see the measurements above?
  3. davidski

    When/What year did OKLAHOMA JOES get sold to charbroil?

    tuning plates are amazing if done right. without them the left side of the smoker is 220 degrees where the right side by the fire box is 350, burning your meat. the plates spread the heat out and block the direct heat from the box, gettign the chamber withitn 10 degrees of itself in any spot. 
  4. davidski

    Brinkmann Fans! Landmann has picked up the torch for you.

    OK joes are owned by Charbroil.  If you buy any Charbroil product, get a OKJ, do nto get anythign with charbroil on it, thats entry level and thinner steel.  Now that image is the OKJ highland. thats 40% smaller than the Brinkmann Trailmaster, Landmann Smokeymountain, OKJ Longhorn.  Highlands...
  5. davidski

    Brinkmann Fans! Landmann has picked up the torch for you.

    i dont understand your question.  Charbroil is entry level $99, 150 and $200 smoker models with less than 3/16th "steel" , High end Charbroil is actually Oklahoma joes, which has 1/8". Brinkmann Long horns used to bridge the gap at $330 with thicker steel, but no welding. I had my longhorn for...
  6. davidski

    When/What year did OKLAHOMA JOES get sold to charbroil?

    thats a ranger. thats the last smoker youll ever need to buy sir. 
  7. davidski

    oklahoma joe smoker?

    i believe thats called a Ranger. came in 2 models, the same smoker, just wider chamber diameter. 
  8. davidski

    Brinkmann Fans! Landmann has picked up the torch for you.

    well... heres how to find their stores.  http://www.bjs.com/webapp/wcs/stores/servlet/LocatorIndexView And its a brinkmann trailmaster, so a little thicker than 1/8".  Everything is screwed on so youll need RTV gasket seal. 
  9. davidski

    My Oklahoma Joe Longhorn BLOG

    Here you go! These are the numbers before and after i cut the 45s with the grinder.  May i suggest going to a metal fab supply,  this metal ran me about 90$, where the fab store by my house was around 45$ If you want to save money, do angle iron instead of C-Channel, and weld a 2nd piece of...
  10. 900x900px-LL-47b9604f_20160313_144506.png

    900x900px-LL-47b9604f_20160313_144506.png

    • davidski
    • Media item
    • Comments: 0
    • Album: My Oklahoma Joe Longhorn BLOG
  11. davidski

    My Oklahoma Joe Longhorn BLOG

    thanks!
  12. 20160326_152203.jpg

    20160326_152203.jpg

    • davidski
    • Media item
    • Comments: 1
    • Album: My Oklahoma Joe Longhorn w/mods
  13. 20160326_152157.jpg

    20160326_152157.jpg

    • davidski
    • Media item
    • Comments: 0
    • Album: My Oklahoma Joe Longhorn w/mods
  14. 20160326_151209.jpg

    20160326_151209.jpg

    • davidski
    • Media item
    • Comments: 0
    • Album: My Oklahoma Joe Longhorn w/mods
  15. 20160326_145118.jpg

    20160326_145118.jpg

    • davidski
    • Media item
    • Comments: 0
    • Album: My Oklahoma Joe Longhorn w/mods
See more
Top Bottom
Back
Clicky