Recent content by bearface

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. bearface

    need help with my reverse flow design please

    Cheers guys I'm going to put the thicker plates top and bottom. Iv marked up that 1/4 plate and have enough left for heat deflector to extend about 6" into cc. Hope to make a good start on it this weekend
  2. bearface

    need help with my reverse flow design please

    Thanks a lot dave was panicking for a while. Can't belive how lucky that turned out! Can build my fire box this weekend rather than go backwards fixing my mistake Iv got two pieces of 20"x20" 10mm (half inch I think) plate to use on fire box and similar amount of 1/4" plate. Was wondering Where...
  3. bearface

    need help with my reverse flow design please

    Cheers len just used this and must admit I thought when I first saw it id never make it work but fair play to dave it's really easy to use. step by step instructions no problems. Really impressive. I fine tuned my dimensions and did calculations based on 16" pipe 33" long and it told me opening...
  4. bearface

    need help with my reverse flow design please

    Think the penny has dropped now mate.I will try and make the area between fb and cc 18 square ". Which is good because easier to lower baffle than weld more on to raise
  5. bearface

    need help with my reverse flow design please

    Hi dave cheers for replying mate. I'm getting well confused. iv followed the link on this post to feldons page By half moon does it mean a semi circle? I was hoping to put a semi circle in the cc
  6. Screenshot_2015-04-30-06-59-10.png

    Screenshot_2015-04-30-06-59-10.png

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
  7. bearface

    need help with my reverse flow design please

    I have enough plate to make a square box so will keep the half moon shape So I hope to just weld a strip in this to reduce diameter down to 6.7". Any help would be really appreciated As im not sure if I do need to make it that small or not. Thought I was on to a winner until I Re read Garys...
  8. DSC_0897.JPG

    DSC_0897.JPG

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
  9. DSC_0896.JPG

    DSC_0896.JPG

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
  10. bearface

    need help with my reverse flow design please

    Also think iv messed up the opening from cc to fire box. Sorry Gary for some stupid reason iv cut out a half moon shape. On your diagram it shows 3" from C iv done 3 1/4 inches from bottom of cc to top of cut. A nightmare if this needs to be bigger as iv cut and tack welded baffle in place I...
  11. bearface

    need help with my reverse flow design please

    Been a busy few months for me with a new baby he's 9months now so iv got a little bit more time to myself and have started work on the smoker again. Just put a temporary handle on cc for now. I'm looking to start fab on cc door seal. Unsure what gauge plate to use it have several sheets off...
  12. DSC_0218.JPG

    DSC_0218.JPG

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
  13. DSC_0217.JPG

    DSC_0217.JPG

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
  14. DSC_0216.JPG

    DSC_0216.JPG

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
  15. DSC_0212.JPG

    DSC_0212.JPG

    • bearface
    • Media item
    • Comments: 0
    • Album: need help with my reverse flow design please
See more
Top Bottom
Back
Clicky