MES 30 Electrical Modification help

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

daveomak

SMF Hall of Fame Pitmaster
Original poster
OTBS Member
★ Lifetime Premier ★
Nov 12, 2010
27,123
4,978
Omak,Washington,U.S.A.
I am thinking about installing a  rheostat on the heating element. The element is an 800 watt.

I am trying to "slow down" the heating cycle at low temps to reduce over shooting the set temp.

Will a rheostat work? What would be the drawbacks?

This is one unit, not necessarily the one I would purchase, but would it work?

 
If my thinking is flawed, what direction do I need to go?

Dave
 
Last edited:
 I would be very careful how you mount it. Were you going to put it inline in like a 4x4 metal box, or mount it on the unit? That dimmer should handle it but if it is the one I'm thinking of there is also a heat sink that comes with it that you will need to install. Your heating element at max should only draw 6.66 amps of current if my math is right. If you hook it stright inline with the power cord not sure what you are going to do to the electronics on the unit with the voltage drop.
 
Quote:
Originally Posted by BAMAFAN  


 I would be very careful how you mount it. Were you going to put it inline in like a 4x4 metal box, or mount it on the unit? That dimmer should handle it but if it is the one I'm thinking of there is also a heat sink that comes with it that you will need to install. Your heating element at max should only draw 6.66 amps of current if my math is right. If you hook it stright inline with the power cord not sure what you are going to do to the electronics on the unit with the voltage drop.
I am thinking of putting the rheostat in an exterior type box on the outside of the smoker.

I would break the wires at the heating element.

I am not sure of the name of the switch but I think it is a double pole/double throw.

The power from the controller would go to the switch and I could switch between the factory element or run the power thru the rheostat.

With that configuration, low temps could be on the rheostat and high temps would be factory configuration.

High temp wire and connectors would be used.

I have not pulled the cover on the wiring yet. Still thinking. I probably would run flex from the cover to the top of the smoker where the new box

and rheostat would be installed.

Does this make GOOD sense? I know enough about electricity to be dangerous.
 
Ummmm Dave....

Is your hobby smoking meats and making sausage or fiddling with yer smoking equipment??

Hehehehehe...Hope you are having fun!!
 

  Craig
 
Why not just wire in a oven controll and tstat?
 
Originally Posted by fpnmf  


Ummmm Dave....

Is your hobby smoking meats and making sausage or fiddling with yer smoking equipment??

Hehehehehe...Hope you are having fun!!
 

  Craig
Craig, Morning. I fool with everything. I like to see how stuff is made, designed, how it was intended to work and how it can be improved.

Everything can be improved. I may not be able to improve it but someone can.

Keeps me busy and drives the wife nuts.
wife.gif

 
 
Craig, Morning. I fool with everything. I like to see how stuff is made, designed, how it was intended to work and how it can be improved.

Everything can be improved. I may not be able to improve it but someone can.

Keeps me busy and drives the wife nuts.
wife.gif

 
Believe me..I know the drill.

As a lifelong mechanic (20+ years as an HD dealer wrench) I suffered from the same addiction...

Pretty much got over last year after the wreck.

Now just enjoying being alive!!

 Have a great day bud!!

  Craig
 
Sounds like it should work.   You may have problems with the controller if you reduce the current flow to the heater by reducing the voltage with the power stat.  The controller on your MES is time proportioned and “tuned” to run with the heater provided, if you change the wattage by using the power stat it may overshoot or undershot the temp setpoint.  But what the heck, give it a try.   After all the heater will get tired over years of service and lose some of its output wattage naturally over time.
 
Why not just wire in a oven controll and tstat?


Tried that and did not work.  Oven control is for 220v not 110v.

I also tried a dimmer, but the controls did not work when I turned down the power.

I DID NOT try to split the wires at the element.  This should be an easy thing to do!

TJ
 
Last edited:
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky