Homegrown sawdust for AMNS?

Discussion in 'Info and Practices' started by czarcastic, Jan 31, 2011.

  1. Sorry if this is a taboo subject.

    I tend to make a LOT of sawdust with my other hobby.  So I was wondering if anyone has had any experience using their own sawdust mix in their AMNS.

    I figure between the bandsaw, tablesaw, planer and lathe, I probably fill up a 30-gallon trash can every month with shavings.

    Anyone else use their own?  Any suggestions?
     
  2. fpnmf

    fpnmf Smoking Guru OTBS Member

    Fl
    It's all hardwood??

      Craig
     

  3. Yes, and I can even keep wood types separate since I usually only use one type of wood in a project/
     
  4. smokinal

    smokinal Smoking Guru Staff Member Moderator OTBS Member ★ Lifetime Premier ★

    Why not give it a try?  
     
  5. scarbelly

    scarbelly Smoking Guru OTBS Member

    The only suggestion I have is that you need to keep it the same consistancy as what Todd sells so it will work correctly. If it is too fine or too corse it will not work well. Give it a try
     
  6. jirodriguez

    jirodriguez Master of the Pit OTBS Member SMF Premier Member

    Wonder if you could get one of those industrial super blenders they sell at Costco - run your stuff through it in batches till you get the consistancy you want..... Just dont do it with the wifes kitchen blender or she might be tempted to run you through the blender.... lol.
     
  7. les3176

    les3176 Master of the Pit

    I would think that if it is too fine most of it will go through the holes. Scar is right you need a good consistant dust. I'm not sayin that fine dust won't work,cause it might but in todd's dust there is a mixture of bigger chips in along withe the finer particals.
     
  8. fpnmf

    fpnmf Smoking Guru OTBS Member

    Fl
    Try it out.

    keep us posted.

     Have a great day!!

      Craig
     
  9. tjohnson

    tjohnson Smoking Guru Staff Member Moderator Insider OTBS Member SMF Premier Member


    Not taboo at all, but a GREAT question!!

    Planer, shaper & lathe chips won't work because they have a little "Curl" to them.

    Depending on the size of the sawdust from your bandsaw, it may be too fine.

    Now, sawdust from your table saw or a miter saw should be absolutely "PERFECT"!

    A 5 gallon bucket goes a very long way in the AMNS, so if you have a project where you're using your table saw or miter saw, it may be in your best interest to save this sawdust.  It may burn a little faster, but what the heck, It's Free!  Also, keep your sawdust in a sealed bag, or it will absorb humidity from the air.

    Also, keep in mind that you want to save Hickory, Alder, Cherry and possibly other hardwood sawdust.  Pine and other soft woods are not recommended.

    Hope This Helps!

    Todd
     
    dale5351 and fpnmf like this.
  10. jirodriguez

    jirodriguez Master of the Pit OTBS Member SMF Premier Member

    .... and all else fails you can always hit Todd up for a bag or three! [​IMG]
     
  11. dale5351

    dale5351 Smoking Fanatic

    As usual, Todd has lots of good info to share.  Even better than a sealed bag is a left over juice jug -- I drink a lot of Ocean Spray Cranberry mixes and keep the empty jugs to store sawdust in.  It was a suggestion I picked up from a post here.  Just remember to label the jugs as to what is in them.
     
  12. justpassingthru

    justpassingthru Smoking Fanatic OTBS Member

    Todd is correct about the miter saw and the table saw, they work fine, I use the dust bag on the miter saw to collect the dust (it's brand new, never used it before, then toss it in the washing machine after each type of wood, ...while mama's at work), but the table saw is too much of a hassle to clean up for smoking saw dust.

    Oops, I use my joiner set at just under 1/8" for the larger pieces, then smash them a little in a 5 gallon plastic bucket with the end of a 2x4 ...guess my blades are getting dull.  [​IMG]

    Gene
     
  13. Thanks everyone - and especially Todd - for your answers.  I've still got plenty of dust from my recent AMNS purchase, so it may be a while before I actually need any.

    Todd - Thanks for your honesty and forthrightness.  Not too many business owners would do that and it says a lot about you.  Kudos to you!  [​IMG]
     
    fpnmf likes this.
  14. grahd

    grahd Fire Starter

    [​IMG][​IMG]
     

Share This Page