First brisket - is this normal?

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

shag

Newbie
Original poster
Jun 15, 2009
12
10
Walking through Costco the other day, I grabbed a small brisket on a whim, as I'd heard they were good to smoke.  After reading a bit, I apparently have a flat - it's small, at 3.8lbs.  I put on a dry rub last night, and wrapped it up overnight.  Threw it on the smoker this morning at 8:45am.

It's now almost 3:45pm (7 hours, for the math challenged), and it's only at 154 degrees.  I've had it on an Electric Brinkmann, between 230 - 240 the entire time.  Is this normal?  I know there's a lot of variance in smoking, but this seems extremely slow for a small cut of meat.

Any suggestions or ideas?  Should I just wait it out, or foil it and throw it in the oven?
 
Is your temp guages(pit,food) correct? If so, then just wait it out 
head-wall.gif


Sometimes the stall can be long, even reverse the internal temp in some cases.
102.gif
 
Is your temp guages(pit,food) correct? If so, then just wait it out 
head-wall.gif


Sometimes the stall can be long, even reverse the internal temp in some cases.
102.gif


As far as I'm aware, they're correct - I'm using a brand new Maverick thermometer...

I expected the plateau to be at a higher temp - the extremely slow crawl at the lower temps surprised me.  I hope it picks up soon - it's already looking like a late dinner - so much for the 90 minutes/lb, lol...

I'm planning on foiling at 160 - would it make sense to throw it in the oven at a slightly higher temp at that point?  If so, what temp?
 
Last edited:
Shag, the dreaded stall can happen just about time. It's not unusual to have one hit when the meat is in the 150° IT range. It's not unusual to have a brisket to have a couple of stalls especially when you're doing a whole packer brisket.
 
As far as I'm aware, they're correct - I'm using a brand new Maverick thermometer...

I expected the plateau to be at a higher temp - the extremely slow crawl at the lower temps surprised me.  I hope it picks up soon - it's already looking like a late dinner - so much for the 90 minutes/lb, lol...

I'm planning on foiling at 160 - would it make sense to throw it in the oven at a slightly higher temp at that point?  If so, what temp?
 You could foil and place in the oven, But i wouldn't go any higher on the temp.
 
The brisket is cooking away in the oven, up to 175 now.  With just a flat, should I pull it out at 190?  195?
 
Sorry i'm late, I would pull at 195º and let rest as long as possible.

If it's time for dinner slice and serve immediately, as it will dry out as soon as you slice it.
 
I just did a flat that was 6.46 lbs.  Took about 7.5 hrs at 250 in my Lang to reach 198.  I coolered it and she rose on up to 212.  Was a good brisket.  Dutch is correct.  Stalls happen and it is just a matter of patience.  By the way , I cooler my briskets and pork roasts at least 45 minutes.  They will continue to climb in temp and distribute the moisture through the meat.  This is also in my opinion when optimum tenderness occures.  Just for curiosity sake I have carved some almost the moment they came out the the smoker and the results were hit and miss.
 
I have a 15 lb packer going in at midnight tonight and don't really expect it to be ready until dinner.  If that give you an Idea.  The stall will wash out many a faint hearted smoker.

Be patient, it will pay off. Cook to temp not time.  

I hope dinner isn't too late tonight.  I know we have had late dinners before.

Good luck.

Don't forget the pictures. Because as you know from Roll Call (if you haven't stopped by you might want to so we can get to know you)  

th_nopicsye3.gif
 
double post - ignore...
 
Last edited:
Thanks for the input.  I ended up taking the brisket to 200, which took just over 11 hours, for a 3.8lb flat - that seems like a crazy long time.  Because it took so long, I didn't have the luxury of letting it rest more than about 15 minutes.  I didn't make note of the grain prior to smoking it, so I tried to figure that out after the fact, and I *think* I got it right - not positive on that, though.

The brisket was decent, not great.  I haven't had good brisket in many, many years, so I'm not exactly sure what to expect, but it was a little tougher than I had anticipated - perhaps I've been spoiled by pork, lol.  The smokey flavor was quite good, though, and I actually found that I liked it better after being reheated over the next couple days.  Go figure.

Am I crazy to think that 11+ hours for 3.8lbs is extraordinarily long?  Not sure how to plan the timing for next time.  It also sounds like I need to take the internal temp to 205 next time, note the grain, and hopefully have time to give it a proper rest after the smoke...

I'm not sure where to find packer briskets locally, but if I can, does the process differ much?  Do I keep the temp probe in the flat, or the other part?
 
The meat can make you crazy.  If you REALLY know the temps in your smoker and the Internal Temps of the meat, you just have to wait it out.  You can't just throw a piece of meat on the smoker and say it is going to be ready at a certain time.

Good luck and good smoking.
 
how long do you keep it in the cooler
For a small flat I would say minimum of 30-45 minutes, for a full packer I generally go 1-2 hrs. But I also usually allow an extra 4 hrs. in my guestimate of cook time, so that way I don't end up ordering pizza for dinner.
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky