cc is going to be 20"x48" how wide should I cut door.I know to cut it at 12 and 3 it's going to be rf so you won't be able to use several inches on the left side anyway right.??
Door size
- Thread starter bishgeo
- Start date
-
Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.
kc5tpy
Master of the Pit
Hello. I assume you mean that the firebox is on the left so the left side will be hotter. The design of the reverse flow is just for that purpose. It draws the heat quicker through the smoker so that you have a more even heat from one end to the other than you would have in a normal offset. The firebox end may always be slightly hotter but that can be used to your advantage. I wouldn't restrict access to either end. I would leave 3"- maybe 4" from each end and cut the door. I don't know your experience but may I suggest you cut the top of the door first, let the cut cool so that you can comfortable lay your hand on it. Tack weld on your hinges at this point, pretty solid tacks. Then finish cutting your door. All should then be completely aligned. Hope this helps. Keep Smokin!
Danny
Danny
No firebox on right just meant u really wouldn't want any thing clear out on end of rack where heat was coming up from under rf plate.I marked cut 3" from end and at 12-3.
KC5TPY, I think what he means is you don't necessarily want to have your cooking grate hang over the opening at the end of the reverse flow plate (opposite end of the firebox) so what I did was figured how much space I needed for that opening to give me the cubic inches I needed (width of the plate times the distance from the end of the plate to the wall of th CC) then I made my door cut there, as well as the edge of me cooking rack. I used the even spacing on the opposite side of the door as well so the whole CC looks even and proportional.
On my build, my plate is about 7 inches off of the bottom (24 diameter pipe) which gave me a width of approximately 22" wall to wall. So 6 inch long opening times 22" wide gave me the opening that I needed. So I cut my door 6" from either side.
On my build, my plate is about 7 inches off of the bottom (24 diameter pipe) which gave me a width of approximately 22" wall to wall. So 6 inch long opening times 22" wide gave me the opening that I needed. So I cut my door 6" from either side.
Last edited:
ribwizzard
Master of the Pit
Ive seen where the door is not perfectly centered, an it looks alright if the trim is done well. Or you could build your end cap to allow for the air to flow, and utilize more of your pipe for cooking area.
CC size will be 20"x48" if that helps with measurements for opening at end of RF plate to door opening.I have it measured to cut 3" from each end but can be changed quick.
ribwizzard
Master of the Pit
kc5tpy
Master of the Pit
Hello. Yep! Now I see what the question was. I still stand by the fact that a hotter end can be a useful thing. Not used all the time but handy to have. I wouldn't make it hard to get to. Not every piece of meat is the same thickness. Why make that end hard to get to when the door size doesn't affect the efficiency of the smoker. GREAT question there RW. I can see where a flat end may "push" more heat to that end of the grill where a "domed" end might tend to roll the heat over the end. By God son you know some stuff about building smokers. Are you sure you ain't from Texas??
Danny
Danny
ribwizzard
Master of the Pit
Nope, from Florida, we don't get a lot of notoriety for our BBQ like Texas does, but we do know how to cook.
Thread Starter
cc is going to be 20"x48" how wide should I cut door.I know to cut it at 12 and 3 it's going to be rf so you won't be able to use several inches on the left side anyway right.??
ReplyQuote Multi
post #2 of 9
3 days, 11 hours ago
Hello. I assume you mean that the firebox is on the left so the left side will be hotter. The design of the reverse flow is just for that purpose. It draws the heat quicker through the smoker so that you have a more even heat from one end to the other than you would have in a normal offset. The firebox end may always be slightly hotter but that can be used to your advantage. I wouldn't restrict access to either end. I would leave 3"- maybe 4" from each end and cut the door. I don't know your experience but may I suggest you cut the top of the door first, let the cut cool so that you can comfortable lay your hand on it. Tack weld on your hinges at this point, pretty solid tacks. Then finish cutting your door. All should then be completely aligned. Hope this helps. Keep Smokin!
Danny
ReplyQuote Multi
post #3 of 9
3 days, 11 hours ago
Thread Starter
No firebox on right just meant u really wouldn't want any thing clear out on end of rack where heat was coming up from under rf plate.I marked cut 3" from end and at 12-3.
ReplyQuote Multi
post #4 of 9
3 days, 11 hours ago
KC5TPY, I think what he means is you don't necessarily want to have your cooking grate hang over the opening at the end of the reverse flow plate (opposite end of the firebox) so what I did was figured how much space I needed for that opening to give me the cubic inches I needed (width of the plate times the distance from the end of the plate to the wall of th CC) then I made my door cut there, as well as the edge of me cooking rack. I used the even spacing on the opposite side of the door as well so the whole CC looks even and proportional.
On my build, my plate is about 7 inches off of the bottom (24 diameter pipe) which gave me a width of approximately 22" wall to wall. So 6 inch long opening times 22" wide gave me the opening that I needed. So I cut my door 6" from either side.
ReplyQuote Multi
post #5 of 9
3 days, 11 hours ago
Ive seen where the door is not perfectly centered, an it looks alright if the trim is done well. Or you could build your end cap to allow for the air to flow, and utilize more of your pipe for cooking area.
My opinions and suggestions are just like my farts, they never stop.
ReplyQuote Multi
post #6 of 9
3 days, 9 hours ago
Thread Starter
CC size will be 20"x48" if that helps with measurements for opening at end of RF plate to door opening.I have it measured to cut 3" from each end but can be changed quick.
ReplyQuote Multi
post #7 of 9
3 days, 9 hours ago
Are you going with flat end caps?
My opinions and suggestions are just like my farts, they never stop.
ReplyQuote Multi
post #8 of 9
3 days, 7 hours ago
Hello. Yep! Now I see what the question was. I still stand by the fact that a hotter end can be a useful thing. Not used all the time but handy to have. I wouldn't make it hard to get to. Not every piece of meat is the same thickness. Why make that end hard to get to when the door size doesn't affect the efficiency of the smoker. GREAT question there RW. I can see where a flat end may "push" more heat to that end of the grill where a "domed" end might tend to roll the heat over the end. By God son you know some stuff about building smokers. Are you sure you ain't from Texas??
Danny
ReplyQuote Multi
post #9 of 9
3 days, 6 hours ago
Nope, from Florida, we don't get a lot of notoriety for our BBQ like Texas does, but we do know how to cook.
- bishgeo
-
- online
- 30 Posts. Joined 3/2014
- Location: springfield oh
- Points: 10
cc is going to be 20"x48" how wide should I cut door.I know to cut it at 12 and 3 it's going to be rf so you won't be able to use several inches on the left side anyway right.??
ReplyQuote Multi
post #2 of 9
3 days, 11 hours ago
- KC5TPY
-
- offline
- 1,440 Posts. Joined 5/2013
- Location: Newark on Trent, United Kingdom.
- Points: 44
Hello. I assume you mean that the firebox is on the left so the left side will be hotter. The design of the reverse flow is just for that purpose. It draws the heat quicker through the smoker so that you have a more even heat from one end to the other than you would have in a normal offset. The firebox end may always be slightly hotter but that can be used to your advantage. I wouldn't restrict access to either end. I would leave 3"- maybe 4" from each end and cut the door. I don't know your experience but may I suggest you cut the top of the door first, let the cut cool so that you can comfortable lay your hand on it. Tack weld on your hinges at this point, pretty solid tacks. Then finish cutting your door. All should then be completely aligned. Hope this helps. Keep Smokin!
Danny
ReplyQuote Multi
post #3 of 9
3 days, 11 hours ago
Thread Starter
- bishgeo
-
- online
- 30 Posts. Joined 3/2014
- Location: springfield oh
- Points: 10
No firebox on right just meant u really wouldn't want any thing clear out on end of rack where heat was coming up from under rf plate.I marked cut 3" from end and at 12-3.
ReplyQuote Multi
post #4 of 9
3 days, 11 hours ago
- TXSean
-
- offline
- 77 Posts. Joined 8/2013
- Location: Kyle, TX
- Points: 10
KC5TPY, I think what he means is you don't necessarily want to have your cooking grate hang over the opening at the end of the reverse flow plate (opposite end of the firebox) so what I did was figured how much space I needed for that opening to give me the cubic inches I needed (width of the plate times the distance from the end of the plate to the wall of th CC) then I made my door cut there, as well as the edge of me cooking rack. I used the even spacing on the opposite side of the door as well so the whole CC looks even and proportional.
On my build, my plate is about 7 inches off of the bottom (24 diameter pipe) which gave me a width of approximately 22" wall to wall. So 6 inch long opening times 22" wide gave me the opening that I needed. So I cut my door 6" from either side.
ReplyQuote Multi
post #5 of 9
3 days, 11 hours ago
- Ribwizzard
-
- offline
- 1,879 Posts. Joined 5/2012
- Location: Orlando and Tampa Florida
- Points: 48
Ive seen where the door is not perfectly centered, an it looks alright if the trim is done well. Or you could build your end cap to allow for the air to flow, and utilize more of your pipe for cooking area.
My opinions and suggestions are just like my farts, they never stop.
ReplyQuote Multi
post #6 of 9
3 days, 9 hours ago
Thread Starter
- bishgeo
-
- online
- 30 Posts. Joined 3/2014
- Location: springfield oh
- Points: 10
CC size will be 20"x48" if that helps with measurements for opening at end of RF plate to door opening.I have it measured to cut 3" from each end but can be changed quick.
ReplyQuote Multi
post #7 of 9
3 days, 9 hours ago
- Ribwizzard
-
- offline
- 1,879 Posts. Joined 5/2012
- Location: Orlando and Tampa Florida
- Points: 48
Are you going with flat end caps?
My opinions and suggestions are just like my farts, they never stop.
ReplyQuote Multi
post #8 of 9
3 days, 7 hours ago
- KC5TPY
-
- offline
- 1,440 Posts. Joined 5/2013
- Location: Newark on Trent, United Kingdom.
- Points: 44
Hello. Yep! Now I see what the question was. I still stand by the fact that a hotter end can be a useful thing. Not used all the time but handy to have. I wouldn't make it hard to get to. Not every piece of meat is the same thickness. Why make that end hard to get to when the door size doesn't affect the efficiency of the smoker. GREAT question there RW. I can see where a flat end may "push" more heat to that end of the grill where a "domed" end might tend to roll the heat over the end. By God son you know some stuff about building smokers. Are you sure you ain't from Texas??
Danny
ReplyQuote Multi
post #9 of 9
3 days, 6 hours ago
- Ribwizzard
-
- offline
- 1,879 Posts. Joined 5/2012
- Location: Orlando and Tampa Florida
- Points: 48
Nope, from Florida, we don't get a lot of notoriety for our BBQ like Texas does, but we do know how to cook.
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.
Similar threads
Latest posts
-
-
-
Our Second piece of Heaven, Little piece on the Atlantic Ocean- Latest: chilerelleno
Hot Threads
-
Chorizo or Sausage? Help a newbie!
- Started by I-am-Chorizo
- Replies: 52
- Sausage
-
Ready For The Farmers Mkt
- Started by BGKYSmoker
- Replies: 24
- General Discussion
-
Beautiful Sunday here
- Started by crankybuzzard
- Replies: 24
- Blowing Smoke Around the Smoker.
