Another Masterbuilt bit the dust - Help, please!!!

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

wuerstel

Newbie
Original poster
Sep 23, 2010
7
10
First off, hi to all. I've stumbled upon your site by accident and started researching until now my eyes are about to glaze over.

Problem is, our Masterbuilt electric smoker gave up it's ghost. (Purchased @2 years ago at Sam's). Worked very well, until....

Husband already took out the element after taking some fancy measurements and determination that it's the culprit. I would have hoped that only the connectors are bad, but no such luck.

I understand there is no replacement element available, so what are our options? 

Saw some threads about outfitting a smoker with a hot plate, but I wonder if that contraption will last long, since all the controls are inside and exposed to heat and steam. So, I don't know about that.

Second thought I had was to retrofit the smoker box with some sort of gas burner. Would that work? Husband said that lack of oxygen would thwart that option, but I'm nothing if not persistent until proven wrong :-)

By the way, I just purchased one of those Amazen smoke generators today after reading y'all's glowing reviews. So all I really need is a heat source to be able to do some hot smoking.

If you could steer me towards a workable solution, I'd greatly appreciate it.

Barbara
 
...
I understand there is no replacement element available, so what are our options? 
...
First off, welcome to the site, Barbara!

Second, I think that it depends on which model of MES you have as to whether or not the heating element can be replaced.  Have you contacted Masterbuilt yet?

Third, if it *can't* be replaced then I'd stick with an electric element for it.  I don't know enough about the controller to know if it would also work with something else, so you might have to get a PID, too, to control it.

You can search through the build threads for info on electric elements and PID's that people here have been successful with if Masterbuilt can't help you.

Best of luck
 
The earlier models of the MES do not have replaceable elements... You should contact Masterbuilt Customer Service to see if a new box is available for your model.  They are great people to work with.

Also Welcome to SMF, you should post a little about you and your equipment in the Roll Call Thread.  That way everyone can give you a proper welcome and get to know you...
 
Hi again, and many thanks for your replies so far.

Ours is a stainless steel model 20070408, a search for any replacement parts was so far unsuccessful. 

But I think I just found my solution: replacing the burned out  800 Watt element with a 1200 Watt element.here: http://www.smokingmeatforums.com/forum/thread/90390/mes-heating-element-mod

Great step-by-step instructions (as far as I can tell as a total layperson).

We're not sure about the wiring upgrade though.

For the time being, I'm looking forward to try out the cold smoke generator I ordered, as this was something I had been missing all along. 100 degrees F plus just doesn't do it for real Black Forest Ham, old fashioned liverwurst, and the like.

Beer-B-Q, will do. 
 
wuerstel  Welcome to SMF!

Your on the right track, there are several companies that offer electric elements that can replace the OEM element.  However you might have to drill a couple of holes or come up with a way to mount the element.

Since you are taking off the back, go ahead and rewire with 12 gauge wire, and beef up the element connectors.

Last but not least is the controller,  since you are doing the other work, you might consider replacing the controller with a PID controller, it is more accurate and has more features depending on how much money you want to spend.  You should be able to restore your MES to better than new condition with higher watt element, beefed up wiring and new controller for about $150-200.  Since your MES is 2 years old and a Sams model, it is therefore all Stainless.  I have the exact same model, and it is still going strong,  did 12 racks of ribs last weekend,  I believe the all stainless model without the window makes a fantastic platform that should last 20 years with some minor maintenance.

You might want to check out this thread for more info on mods and the fixes already mentioned
 
Wuerstel,

Welcome to SMF!!!

There are a number of threads on SMF regarding upgrading the heating element in your MES.  You can also purchase a replacement element and bend it to the shape you need.

Todd
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky