Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. lizardman

    Grill Cover Recommendations

    I found the Classic Accessory line online as well, chose the 'Hickory' line Grill Cover for my Weber Genesis E-310, will let you guys know how it works out...As I mentioned, I will soon be replacing my Masterbuilt plastic cover for my 30" smoker with a cover from the same Classic Accessory...
  2. lizardman

    Grill Cover Recommendations

    After searching around a bit I'm going with this one, looks like it may last longer than most, they also offer smoker covers, as soon as my Masterbuilt cover starts to crack I'll be getting one of these:
  3. lizardman

    Grill Cover Recommendations

    Just ripped a hole in my grill cover clearing the ice block off my gas grill (we got 8" of snow in North Metro Atlanta!), I have a Weber Genesis 310, any recommendations for a gas grill cover that will last more than a couple of years? Willing to spend a little more for something that will...
  4. lizardman

    Looking for a leave-in digital thermometer

    Nice, how about an instant read thermometer, which one do you use?
  5. lizardman

    Looking for a leave-in digital thermometer

    Cool, thanks Motocrash, the Thermopro TP-20 looks like a safe bet, any reasons to go to a more expensive model? Love the lifetime probe warranty...
  6. lizardman

    Looking for a leave-in digital thermometer

    For use in a Masterbuilt 30, preferably around/under $100, one that I can monitor with Android device would be nice! What's the new technology that everybody is using?
  7. lizardman

    Masterbuilt 30 - Should I leave it plugged in?

    Dang! I was going to ask you about this pain in my lower back...
  8. lizardman

    Masterbuilt 30 - Should I leave it plugged in?

    I was thinking the same Doc, just wanted to get a second opinion....and it came from a Doctor!
  9. lizardman

    Masterbuilt 30 - Should I leave it plugged in?

    I use my Masterbuilt 30 2-3x per month, is there any benefit unplugging it from the outlet after each use? I noticed that it 'beeps' when I plug it in, leading me to believe something's staying energized when it's plugged in...Thoughts?
  10. lizardman

    Another AMNPS-MES Question

    Since I invested in a 20# bag-o-pellets, I bought a dedicated Home Depot orange bucket to store them, it's vacuum tight and has worked well so far. I agree, I stored my first 5# in a heavy-duty ziploc, I feel sure the Georgia humidity got to them, had them stored in The Man Room under the pool...
  11. lizardman

    Another AMNPS-MES Question

    In the FWIW department: I too had a problem keeping my AMNPS lit in my MES 30" Gen 2, even with all of the recommendations (replaced damper with aluminum 90 degree elbow, chip loader pulled out 2" in dump position, moving the AMNPS to the top rack, etc)...I recently purchased a new 20lb bag of...
  12. Another AMNPS-MES Question

    Another AMNPS-MES Question

  13. XXX20150830_174911.jpg

    XXX20150830_174911.jpg

    • lizardman
    • Media item
    • Comments: 0
    • Album: Another AMNPS-MES Question
  14. lizardman

    MES 30" 2nd Gen Grate Dimensions?

    Perfect, thanks Richie for taking the time!
  15. lizardman

    MES 30" 2nd Gen Grate Dimensions?

    Thanks Richie, I'm sure somewhere in your instructions the dimensions of the MES 30" grates are listed, I've read them couple of times and can't get those dimensions, but I'm not a carpenter (I know I'm just missing something)...
  16. lizardman

    MES 30" 2nd Gen Grate Dimensions?

    Couldn't find this easily, being the Lazy Lizard I am thought I'd post this to The Forum, looking for the grate (smoker rack) dimensions of a second generation MES 30" smoker, wanted to get some non-stick mat material...
  17. lizardman

    Another AMNPS-MES Question

    Lisa, You simply unscrew and remove the damper (vent) and push in the 90 degree elbow...One end of the elbow should be bent inwards a little, it fits snug without using anything to keep it attached...at least my MES 2nd Gen 30"...I remove it before I put the cover on, that's pretty important to...
  18. lizardman

    Another AMNPS-MES Question

    I had the same problem Travis...so...a few suggestions... Try lighting the AMNPS *out* of the MES just to make sure it's not the chips. Also, I totally removed the damper and put a 3" 90 degree aluminum exhaust elbow in it's place (pointed upwards), I then moved the AMNPS to the *top* rack...
  19. lizardman

    Charbroil Tru-Infrared Gas Grill Recommendations?

    My sad Brinkman gas grill is falling apart, don't want to spend much over $400 on a new gas grill since I smoke just about everything in my MES 30, any strong opinions on the Charbroil Tru-Infrared gas grill? I like the concept of the flame being underneath the metal 'V' shield between the...
  20. lizardman

    AMNPS Rookie Mistakes

    Per Todd, I moved the Amazen gadget to the top rack, pellets stayed lit and the 'inside turbulence' Todd mentioned was definitely there...As an added smoke source I did a couple of dumps of pellets into the onboard chip loader, they smoke up *SO* much better than wood chips!
Top Bottom
Back
Clicky