Search results
-
Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
-
When smoking on a UDS...
You and me both. It does not pay to be impatient and put the meat on while the smoke is still thick. Took me awhile to connect the bad taste with the startup smoke. I have waited up to 2 hours for the smoke to clear if I had to now. The food tastes MUCH better that way. Yep, I would...- ddave
- Post #8
- Forum: UDS Builds
-
When smoking on a UDS...
What he said although I don't put one in the middle. I wouldn't worry about getting smoke right away. It usually takes an hour or so for the yucky white smoke to clear up on mine anyway. Actually, when it is humming along and all warmed up, you'd be hard pressed to see smoke. But at the end...- ddave
- Post #5
- Forum: UDS Builds
-
UDS Weber Lid Mod
Depends on how much you tighten the bolts. Yes. That's good to know about the adhesive. Dave- ddave
- Post #33
- Forum: UDS Builds
-
UDS Weber Lid Mod
I have that issue to a certain extent but I just rotate the lid until I found a spot to where it sits pretty flat and doesn't rock. It's not perfect and I get some air in through there too, I am sure. I thought about using some woodstove door gasket on the ring or on the inside lip of the lid...- ddave
- Post #27
- Forum: UDS Builds
-
Pork Shoulder Safety
I believe the recommended temps are 225° to 250°. Even temps in the 260s aren't going to hurt a pork shoulder. Since you injected, according to USDS guidelines, it should have hit 140° in 4 hours although I beleive it has been changed to 135° per the 2010 Food Code. If you hadn't injected...- ddave
- Post #6
- Forum: Food Safety
-
UDS Weber Lid Mod
A friend of mine used a circular saw with a metal cutting blade. Nice smooth cut. Dave- ddave
- Post #25
- Forum: UDS Builds
-
The dreaded temp spike when the lid is off.
Lots of ways to make good Q. Dave- ddave
- Post #16
- Forum: UDS Builds
-
How to remove liner
I understand your desire to save money, but I think you'd be happier in the long run if you just bought the unlined drum. If you don't have them already, you may end up spending more than the $45 on masks, goggles, ear plugs gloves and wire wheels by the time you wire wheel the other one out...- ddave
- Post #7
- Forum: UDS Builds
-
The dreaded temp spike when the lid is off.
Water pan . . . in a UDS . . .are you nuts??? Just messing with ya, meateater. If it gets your meat cooked the way you like it then it's the right way to do it. Dave- ddave
- Post #14
- Forum: UDS Builds
-
How to remove liner
Paying someone else to sandblast it would be your best bet. Or find an unlined drum. The liners can be a real pain to get it out and really take the fun out of a UDS build. Dave- ddave
- Post #5
- Forum: UDS Builds
-
Drum burn in questions
Lead wrapped in paper, then plastic, then plastic, then another plastic bag?? I'd say you have nothing to worry about. Certainly safer than one that held petroleum. If it is bare metal inside, no need to burn. Wire wheel any rust spots, if there are any, and get to building. Dave- ddave
- Post #3
- Forum: UDS Builds
-
heat baffle for offset smoker?
Sounds like it's snaking too fast. I'm with Corn Cob -- use less fuel -- learn to control the fire. Otherwise you're wasting fuel. Dave- ddave
- Post #7
- Forum: Charcoal Smokers
-
The dreaded temp spike when the lid is off.
I just have a table nearby with some pieces of angle iron on it that I set the grate on. If I'm doing something that will take some time, I take the grate out and put the lid back on. Another thing that helps is closing the intakes for 3 minutes or so before you remove the lid. Lowers the...- ddave
- Post #9
- Forum: UDS Builds
-
Wanna build a UDS
One of the best if not THE best "how to" UDS thread on the Internet. http://www.bbq-brethren.com/forum/showthread.php?t=43943 Dave- ddave
- Post #7
- Forum: UDS Builds
-
First time using UDS
Excellent, excellent starting method and advice. Dave -
Pork Burnt Ends?
The rack that those were cooked on is 24" from the bottom of my charcoal basket. There is another set of bolts about halfway up the drum that I put an expanded metal grate on sometimes if I'm using the diffuser plate. Even if I'm not using the plate, I'll sometimes put the grate in anyway. I... -
Pork Burnt Ends?
Haven't posted any smokes in awhile so here goes. Been wanting to try something like this for awhile so last night I got some boneless country style ribs and rubbed them with Mad Hunky and into the fridge for the night. Put them on the smoker with hickory at 9 am. Figured I do a 3-2-1 to start... -
UDS dissapointment
Meateater, No disrespect taken and none meant on my part either. I know we've been back and forth on this before. Believe me, if your drum with the door and the water pan runs the way you like it and cooks meat the way you like it, then it doesn't get any better than that. I certainly...- ddave
- Post #30
- Forum: UDS Builds
-
UDS dissapointment
He also uses a water pan which knocks the hell out of the temps. But since he has the door, they probably equalize. I would bet he would have a hard time keeping the temps in the 225° to 250° range without the water pan. I know it works for meateater and he is happy with it and I respect...- ddave
- Post #15
- Forum: UDS Builds
-
UDS dissapointment
Bingo!! Seal the darn door and bring it up to temp slow like rbrastner said and you should be fine. Dave- ddave
- Post #9
- Forum: UDS Builds
