Recent content by kageryu

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. kageryu

    Horizon Marshal Smoker and Temp. Management Problems

    Thanks guys, I used half a chimney and was able to keep my temps around 250.  I can see why there is an art to this as I had to fiddle with the damper and watch the temps go up and down.  I never opened the damper more than about an eighth.  I didn't quite use a whole bag of charcoal this time...
  2. kageryu

    buy one get one free kingsford..

    I just picked up 80lbs for about $16 at Lowes.  A man could do worse. -p
  3. 001.JPG

    001.JPG

    • kageryu
    • Media item
    • Comments: 0
    • Album: Default
  4. 001.JPG

    001.JPG

    • kageryu
    • Media item
    • Comments: 0
    • Album: Default
  5. 031.JPG

    031.JPG

    • kageryu
    • Media item
    • Comments: 0
    • Album: Default
  6. 036.JPG

    036.JPG

    • kageryu
    • Media item
    • Comments: 0
    • Album: Default
  7. 036.JPG

    036.JPG

    • kageryu
    • Media item
    • Comments: 0
    • Album: Default
  8. kageryu

    Horizon Marshal Smoker and Temp. Management Problems

    Thanks Al, I will try that.  I guess I should post some pics as well. -p
  9. kageryu

    Horizon Marshal Smoker and Temp. Management Problems

    Hey Guys, I bought a new Horizon Marshal 20'' smoker in the early spring and I've been using it all summer.  I've made some ok stuff on it, but I have not been able to perfect my temperatures in the pit.  It has a factory built sliding convection plate (it is currenlty all the way to the right...
  10. kageryu

    Looking at a Horizon Smoker

    Hey Guys, I know it has been a while.  I think the smoker is scheduled to be built some time this week, so it won't be long now.  I have a question about the thermometers.  I am going to replace the stock thermometers with Tel-Tru thermometers, but I'm unsure on which stem size to buy.  I was...
  11. kageryu

    Looking at a Horizon Smoker

    Hey Guys, I have a quick question for anyone that owns a Horizon Smoker.  I've seen a lot of posts stating that the stock thermometers are pretty inaccurate.  I was planning on picking up some tel-tru thermometers.  So, my question is do I also need to pick up the installation kits with the...
  12. kageryu

    Looking at a Horizon Smoker

    Well, I pulled the trigger on the Horizon Marshal Today.  It was hard to pass up the Bell Smoker, but I've been wanting the Horizon for a while and I think I made the right decision.  The people at Horizon were very nice to talk to and I can't wait for my smoker to be built.  Once it comes, I...
  13. kageryu

    Looking at a Horizon Smoker

    Hello Rick, That is a real good point.  It seems that the Horizon smoker is becoming the standard I compare the other smokers too.  I'm not saying the other vendors are not as good, but I guess in my mind this might be the best one for me.  I'll try and contact the factory again about a...
  14. kageryu

    Looking at a Horizon Smoker

    Does anyone have opinions about Bell Fabrications?  http://www.bellfab.com/ I've been doing some reading in various forums and he seems to have some very reasonable prices.  What is the best way to even out the temperature in the smoker chamber?  If I decide to go with him, I will need to tell...
  15. kageryu

    Looking at a Horizon Smoker

    Yes, the Lang smokers look real nice.  However, I'm not sure if they will ship to NJ and that would be one heck of a drive to pick up a smoker. What is the consensus on Horizon vs Lang?  I sure this is an age old debate and I apologize if this has been answered 100's of times on the board. I...
See more
Top Bottom
Back
Clicky