Recent content by crawfishslayer

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. image.jpeg

    image.jpeg

    • crawfishslayer
    • Media item
    • Comments: 0
    • Album: 250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)
  2. image.jpeg

    image.jpeg

    • crawfishslayer
    • Media item
    • Comments: 0
    • Album: 250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)
  3. image.jpeg

    image.jpeg

    • crawfishslayer
    • Media item
    • Comments: 0
    • Album: 250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)
  4. crawfishslayer

    250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)

  5. 250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)

    250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)

  6. image.png

    image.png

    • crawfishslayer
    • Media item
    • Comments: 0
    • Album: 250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)
  7. crawfishslayer

    250 Gal Reverse Flow Smoker on Trailer (Mooresville, NC)

    This smoker is constructed from a 250 gallon propane tank and mounted to a 13.5' boat trailer. The tank is 5/16" thick steel and measures approx. 30"x 94". Firebox is 28"x24"x24" and built out of new 1/4" steel plate. The trailer has new tires and I had new leaf springs installed a few years...
  8. crawfishslayer

    Long Time Smoker, First Time Welder (250 gal RF)

    Got a few things done this past weekend. 2 vents installed. 1 on each side of firebox. 3"x8" Smoke stack put in place. 28" extends outside the cooking chamber. Extends into the tank about 6 more inches. I lit a test fire in the firebox just to see if the draw was good. As you can see...it...
  9. IMG_9800.JPG

    IMG_9800.JPG

  10. IMG_9793.JPG

    IMG_9793.JPG

  11. crawfishslayer

    First Brisket w/ Q-view

    How far are you from Mooresville NC? I'd love to stop by for lunch if there are leftovers!
  12. crawfishslayer

    Long Time Smoker, First Time Welder (250 gal RF)

    Hey irvvfsmokin, I do have more photos. They don't show every step of the process but they might be helpful. Send me a private message with your email address and I will send you some of them. I'll be honest with you, I had no written plans for this build. All I had was 10 years of photos and...
  13. crawfishslayer

    Long Time Smoker, First Time Welder (250 gal RF)

    Raptor, How did you make this handle? Did you make it from a chipping hammer or did you buy the coil and bend a piece of rod to put it on? How much clearance do you have from the handle to the tank? In other words, when you grab the handle how close are your knuckles to the tank? I might have...
  14. crawfishslayer

    Long Time Smoker, First Time Welder (250 gal RF)

    Had a few hours to work today. Got all 4 shelves built. Instead of welding the center support for the upper shelves, I bolted it. If I remove the 3 bolts the entire bracket can be removed to accommodate a large animal on the bottom shelves. I have a 125 pig to smoke next month and it would not...
  15. IMG_9659.JPG

    IMG_9659.JPG

See more
Top Bottom
Back
Clicky