DIY Cold Smoker - New at it, built my own - check out the short video - want to see more?

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.
Looks great - you've got a nice looking place there!  Does the smokehouse have a chimney or outgoing vent?  If not, it may help with getting a bit of movement through the vacuum.
 
No we don't have a chimney or outside because we get enough leakage through without one.  We have a good draw, and only had to use 6 logs for an 18 hour smoke.

Knowing this now, would you still recommend a chimney?
I will post a photo of my steps making this smokehouse... with each reply if interested
 
You say you have lots of questions. What are they? Photos of your smoker will help answer questions so post away. Can't watch your video so have no idea what your smoker looks like...
 
Well I have a homemade cold smoker.  I have never, until last weekend, cold smoked.  I did bacon and salmon.  Kept the temp under 100 degrees the entire time, used minimal wood, and had a good solid flow of smoke in the house.

I am more now looking for receipts, tips etc of cold smoking....

I will upload photos of the smoker for you to see.












































when you go through the pics, you will see the pit got a facelift... I used a small opening, but couldn't really hold smoke, so I used firebrick, insul-stick and the cast iron door to lock it down.
 
 
No we don't have a chimney or outside because we get enough leakage through without one.  We have a good draw, and only had to use 6 logs for an 18 hour smoke.

Knowing this now, would you still recommend a chimney?
Yes I would still recommend a chimney to ensure a good steady air flow through the smoker. This will help reduce tar build up in the smoke house over time and help prevent it from depositing onto the food - even though most of the tar should condense in the cooling duct.

For some smoked foods (e.g. traditional smoked salmon or Jerky) the smoking process is as much about reducing the moisture content as it is about applying a smoke flavour. This requires there to be a good steady flow of smoke/air over the meat.

I am pleased that the bacon turned out well. There is nothing quite as good as home smoked bacon.
 
 
Yes I would still recommend a chimney to ensure a good steady air flow through the smoker. This will help reduce tar build up in the smoke house over time and help prevent it from depositing onto the food - even though most of the tar should condense in the cooling duct.

For some smoked foods (e.g. traditional smoked salmon or Jerky) the smoking process is as much about reducing the moisture content as it is about applying a smoke flavour. This requires there to be a good steady flow of smoke/air over the meat.

I am pleased that the bacon turned out well. There is nothing quite as good as home smoked bacon.
I agree on the chimney.  Even though you're getting a good vacuum with the leakage in the structure, having one, central chimney off to the side would give a better vacuum IMHO.  I recommend a chimney to the side so nothing drips down over your meats.  With a good strong vacuum through one designated vent, you'll see the leakage from the structure reduced I imagine, plus it should help minimize an "stale smoke" hanging around.  Hope this helps!  And again, really nice job!  It looks awesome!
 
Moose....  nice smoker.....  I would drill a few holes up near the peak for improved air flow..  A stack will collect condensate and depending where it was installed, it could drip creosote on the food....    Sidewall venting has always worked for me...  
 
soffit buttons are pretty restrictive to air flow...  I'm thinking you may need a bit more than they would allow...
 
Just trying to add the right size for proper flow, without taking away from the nice neat look we have made... so you are suggesting a pretty large opening then?
 
If you had several 1.5" or 2" holes and covered over with hardware cloth... 1/4" or 3/8" holes.....   the smokehouse is the exhaust stack...  it just needs somewhere to exhaust because is pretty air tight...  say you drilled 4 holes in a somewhat symmetrical fashion....  checked the air flow... maybe drill a few more or not,..  It's trying to achieve a balance of air in...   air out... and a good flow pattern inside the smoker for uniform smoke distribution....   sounds easy huh....   some folks even use adjustable floor registers like in a forced air heating system.....  near the roof and near the floor....  the holes near the floor let in cool air to regulate temperature in the smoker...   it's easier than continually adjusting the fire....

 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Hot Threads

Clicky